Bendpak HD-7W 7,000 Lbs Extra Wide, Extra Tall 4-Post Lift

7,000 Lbs

Factory Shipped

  • Bendpak Plastic Drip Trays Sets Of Two
  • Bendpak JP-3 3,000-Lb. Capacity Sliding Jack Platform For Runway
  • Bendpak RBJ4500 4,500 Lb. Capacity, Rolling Bridge Jack
  • Bendpak DP-30 18 Gallon Rolling Drain Pan
Total Price:
$4,640.00 $3,880.00
(You save $760.00)
Free Shipping
Free Shipping

Factory Shipped

Bendpak HD-7W 7,000 lb Extra Wide, Extra Tall 4 Post Lift

Get the most out of smaller spaces and compact vehicles with BendPak’s HD-7P four-post lift. This narrow lift shaves 10.5” off the overall width of the lift, as well as the width between the columns. If you want a 7,000-lb. capacity four-post lift but can’t sacrifice the precious inches taken up by the HD-7W, this is the car lift for you. Store classic cars, racers and compact vehicles comfortably and safely

Bendpak Safe Balancing Bendpak Car Lift Guide Bendpak Top 10 Car Lift Guide Bendpak HD-7W Floorplan


  • 7,000-lb. maximum lifting capacity
  • High lift with short runways
  • Electric / hydraulic power system
  • Single hydraulic cylinder mounted underneath runway
  • Internal anti-sway slider blocks in each column
  • Oversized self-lubricating cable rollers
  • High-speed lifting
  • Features heavy-duty 3/8" aircraft cable
  • Rugged 1.25" roller axles
  • Multi-position safety locks in each column
  • Adjustable lock ladders
  • Ramps feature non-skid surface
  • Push-button pneumatic safety release
  • Optional 4,500-lb. capacity rolling jack available (Model RJ-45)




  • Lifting Capacity*:7,000 lbs. (3,175 kg)
  • *Max Capacity / Front Axle: 3,500 lbs. (1,588 kg)
  • *Max Capacity / Rear Axle:3,500 lbs. (1,588 kg)


  • A - Min. Runway Height: 4.5" (114 mm)
  • B - Max. Rise: 82" (2,083 mm)
  • C - Max. Lifting Height: 86.5" (2,197 mm)
  • Time to Full Rise: 35 sec

Outside Dimensions

  • Overall Width: 110,25" (2.800 mm)
    Outside Length: 174" (4.420 mm)
  • Overall Length: 200" (5.080 mm)
  • Height of Columns: 100" (2.540 mm)

Inside Dimensions

  •  Width Between Columns: 100,25" (2.546 mm
     Drive-Thru Clearance: 86,5" (2.197 mm)


  • J - Runway Width: 19" (483 mm)
  • K - Length of Runways: 164" (4,166 mm)
  • L - Width Between Runways: 37.5" (953 mm) or
  • M - Runway Centerline: 56.5" (1,435 mm) or
  • N - Outside Edge of Runways: 75.5" (1,918 mm) or

Minimum Wheelbase

  • Rated Capacity: 115" (2,921 mm)
  • 75% Capacity: 100" (2,540 mm)
  • 50% Capacity: 85" (2,159 mm)
  • 25% Capacity: 70" (1,778 mm) 


  • Locking Positions: 15
  • Lock Spacing: Every 4" / 102 mm 

Power Unit

  • Motor: 220 VAC / 60 Hz. 1Ph.
  • Noise: 45 db 


Bendpak WSA-100     Bendpak Air Bottle Jack     Bendpak DP-30
           WSA-100                     AIR BOTTLE JACK                       DP-30

* This dimension may be limited with the addition of rolling jacks. See rolling jack specifications on separate page.
** Special Voltages Available Upon Request
The design, material and specifications are subject to change without notice.

Note: An air supply (minimum: 30 psi / 3 CFM) is required for the safety-lock mechanisms to function. It is solely the responsibility of the end-user to provide, install and maintain the air supply.

*Shipping is FREE to direct points within the 48-contiguous states.

**Bendpak charges taxes to California**

**A 5% RATZ Surcharge may apply if shipping to a rural shipping point. Click here to check if you are in a RATZ zone

***It is the buyer's responsibility to unload the freight at their location.

*****Not all BendPak lift models meet the standards as prescribed by ANSI/ALI ALCTV-2006 or ANSI/UL 201. Consult for a complete list.

BendPak 2-Post Lifts and 4-Post Lifts are warranted for five years on equipment structure, to be free of defects in material and workmanship. Power units, hydraulic cylinders, and all other assembly components such as turnplates, slip plates, cables, chains, valves, switches etc. are warranted for one year against defects in material or workmanship under normal use. BendPak Inc. shall repair or replace at their option for the warranty period those parts returned to the factory freight prepaid which prove upon inspection to be defective. BendPak Inc. will pay labor costs for the first 12 months only on parts returned as previously described.


Frequently Bought Together

Please choose options for all selected products

  • Choose Options
    • Bendpak Plastic Drip Trays Sets Of Two
    • Bendpak JP-3 3,000-Lb. Capacity Sliding Jack Platform For Runway
    • Bendpak RBJ4500 4,500 Lb. Capacity, Rolling Bridge Jack
    • Bendpak DP-30 18 Gallon Rolling Drain Pan