Chicago Pneumatic CPXHT75 Refrigerant Dryer
Ideal for use with piston compressors that do not have an aftercooler or where air is over 130 °F
The CPXHT dryers are easy to install and have a compact design. Supplied with 115 Volt power means no special wiring is required and the space saving design incorporates an air cooled aftercooler, refrigerated air dryer, moisture separator and electronic water drain.
The CPXHT dryers are a perfect complement to the RCP line of reciprocating air compressors. With a maximum inlet temperature of 180 ˚F, no aftercooler is required.
All models are equipped with a smart condensate discharger. It discharges only water, NOT compressed air. Silent, eliminating noise pollution. Carefully sized for each model, it assures exceptional reliability and efficiency in discharging water, without compressed air. In case of malfunction, an alarm signal is displayed.
Features
- Dryer rated for temperatures up to 180 °F
- Light and compact design, does not require any special equipment
- Simplified maintenance helps to minimize your service costs
- Electronic controller indicates all relevant technical information about status of the refrigerant dryer as well as dewpoint indication
- Equipped with stainless steel/copper heat exchanger
- Eliminates water, oil and dirt from air systems
- Prevents damage to tools and cylinders, adding to their longevity
- Fewer finished product defects
- Prevents “fisheye” paint splotches
- Reduces operational downtime
- Increases profitability and productivity
- Eliminates air line purging
- Compact design for small footprint
- Quality components for efficient cooling
- Internal layout and enclosure allow for quiet operation
| Model | 50°F PDP cfm @100 psig | Use with | Electrics* V/Ph/Hz | Oper. kW | Heat Exchanger | Max. psig | Refrig. | Weight (lbs) | L (in) | W (in) | H (in) | Conn. (NPT) |
| CPXHT-25 | 25 | 5 & 7.5hp | 115/1/60 | 1/4 | SS/Copper | 232 | R-134a | 57 | 14 | 15 | 18 | 3/4 |
| CPXHT-50 | 50 | 10-15hp | 115/1/60 | 1/4 | SS/Copper | 232 | R-404A | 108 | 18 | 23 | 31 | 1" |
| CPXHT-75 | 75 | 20hp | 115/1/60 | 1/2 | SS/Copper | 232 | R-404A | 168 | 18 | 23 | 31 | 3/4" |
| CPXHT-100 | 100 | 25hp | 115/1/60 | 3/4 | SS/Copper | 232 | R-404A | 231 | 18 | 23 | 41 | 3/4" |
| CPXHT-125 | 125 | 30hp | 115/1/60 | 3/4 | SS/Copper | 232 | R-404A | 236 | 18 | 23 | 41 | 3/4" |
Maximum Ambient 113 ˚F Dew Point Temp 50˚F ± 2 ˚F
Minimum Ambient 41 ˚F Maximum Inlet Temp 180 ˚F
Downloads
- Specs Sheet (page 4)
*The manufacturer collects Sales Tax in all states
Chicago Pneumatic Limited Warranty Policies
General Pneumatic Tools: 1 Year Limited Warranty
Limited Warranty: The “Products” of the Chicago Pneumatic Tool Co. LLC (“CP”) are warranted to be free from defects in material and workmanship for one year from the date of purchase. This Warranty applies only to Products purchased new from CP or its authorized dealers. Of course, this Warranty does not apply to products which have been abused, misused, modified, or repaired by someone other than CP or its Authorized Service Representatives. If a CP Product proves defective in material or workmanship within one year after purchase, return it to any CP Factory Service Center or Authorized Service Center for CP tools, transportation prepaid by customer, enclosing your name and address, adequate proof of date of purchase, and a short description of the defect. CP will, at its option, repair or replace defective Products free of charge. Repairs or replacements are warranted as described above for the remainder of the original warranty period. CP’s sole liability and your exclusive remedy under this Warranty is limited to repair or replacement of the defective Product. (There Are No Other Warranties Expressed Or Implied And CP Shall Not Be Liable For Incidental, Consequential, Or Special Damages, Or Any Other Damages, Costs Or Expenses.)
