Bendpak HD-9XL 9,000 Lbs Capacity Extra Wide 4 Post Car Lift

$4,100.00
$4,100.00
$3,430.00
(You save $670.00 )
Brand:
SKU:
5175859
Condition:
New
Availability:
Factory Shipped
Shipping:
Free Shipping
  • Bendpak JP-3 3,000-Lb. Capacity Sliding Jack Platform For Runway
  • Bendpak Plastic Drip Trays Sets Of Two
  • Bendpak RBJ4500 4,500 Lb. Capacity, Rolling Bridge Jack
  • Bendpak DP-30 18 Gallon Rolling Drain Pan
  • Bendpak Caster Kit Portable Wheel Kit For HD-7 & HD-9 Series

Bendpak HD-9XL 9,000 lbs Capacity Extra Wide, Standard Height, Long Runway Car

The HD-9XL is the ideal 9,000-lb. capacity four-post car lift for vehicles with longer wheelbases. In fact, the runways are about two feet longer than the runways on the standard HD9. This four-post lift variety is available with optional casters, dip-trays, jack platform and more.

Bendpak Leak Proof Will it Fit? Bendpak HD-9SW Floorplan

Safe Balancing Bendpak Car Lift Guide Bendpak Top 10 Car Lift Buyer's Guide

FEATURES

  • 9,000-lb. maximum lifting capacity
  • CE Approved and Certified. Meets or exceeds the standards prescribed by European Standard EN-1493
  • Wide drive-thru with standard lift height and long runways
  • Electric / hydraulic power system
  • Internal "Anti-Sway" slider blocks in each column
  • Features heavy-duty 3/8" aircraft cable
  • Multi-position safety locks in each column
  • Ramps feature non-skid surface
  • Runways include rail-kit for optional accessories
  • Single hydraulic cylinder underneath runway
  • Oversized self-lubricating cable rollers
  • Rugged 1.25" roller axles
  • Adjustable lock ladders
  • Push-button pneumatic safety release
  • Optional 4,500-lb. capacity jack available (Model RJ-45)

qo.jpg

 SPECIFICATIONS 

Capacity

  • Lifting Capacity* 9,000 lbs. (4,082 kg)
  • *Max Capacity / Front Axle 4,500 lbs. (2,041 kg)
  • *Max Capacity / Rear Axle 4,500 lbs. (2,041 kg)

Rise

  • A - Min. Runway Height: 4.5" (114 mm)
  • B - Max. Rise: 70" (1,778 mm)
  • C - Max. Lifting Height: 74.5" (1,892 mm)
  • Time to Full Rise: 50 seconds

Outside Dimensions

  • D - Overall Width: 110.25" (2,800 mm)
  • E - Outside Length: 198" (5,029 mm)
  • F - Overall Length: 224" (5,690 mm)
  • G - Height of Columns: 88" (2,235 mm) 

Inside Dimensions

  • H - Width Between Columns: 100.25" (2,546 mm)
  • I - Drive-Thru Clearance: 86.5" (2,197 mm) 

Runways

  • J - Runway Width: 19" (483 mm)
  • K - Length of Runways: 188" (4,775 mm)
  • L - Width Between Runways: 37.5" (953 mm) or 44.375" (1,127 mm)
  • M - Runway Centerline: 56.5" (1,435 mm) or 63.375" (1,610 mm)
  • N - Outside Edge of Runways: 75.5" (1,918 mm) or 82.375" (2,092 mm)

Minimum Wheelbase

  • Rated Capacity: 135" (3,429 mm)
  • 75% Capacity: 115" (2,921 mm)
  • 50% Capacity: 95" (2,413 mm)
  • 25% Capacity: 80" (2,032 mm) 

Locking

  • Locking Positions: 12
  • Lock Spacing: Every 4" (102 mm)

Power Unit

  • Motor: 220 VAC / 60 Hz / 1 Ph
  • Noise: 45 dB

Shipping

  • Weight: 2,040 lbs. (927 kg)
  • Dimensions: 204" x 22" x 40" (5,182 mm x 559 mm x 1,016 mm)

 

ACCESSORIES:

Bendpak WSA-100     Bendpak Air Bottle jack     Bendpak Plastic Drip Trays     Bendpak Rolling Jack 4,500     Bendpak JP-6
          WSA-100                       AIR BOTTLE JACK         PLASTIC DRIP TRAYS          ROLLING JACKS          SLIDING JACK PLATFORM

Note: An air supply (minimum: 30 psi / 3 CFM) is required for the safety-lock mechanisms to function. It is solely the responsibility of the end-user to provide, install and maintain the air supply.

*Shipping is FREE to direct points within the 48-contiguous states.

**Bendpak charges taxes to California**

**A 5% RATZ Surcharge may apply if shipping to a rural shipping point. Click here to check if you are in a RATZ zone

***It is the buyer's responsibility to unload the freight at their location.

****The Bendpak HD-9XL is an ALI Certified Lift. Click here to view its certification. 

BendPak 2-Post Lifts and 4-Post Lifts are warranted for five years on equipment structure, to be free of defects in material and workmanship. Power units, hydraulic cylinders, and all other assembly components such as turnplates, slip plates, cables, chains, valves, switches etc. are warranted for one year against defects in material or workmanship under normal use. BendPak Inc. shall repair or replace at their option for the warranty period those parts returned to the factory freight prepaid which prove upon inspection to be defective. BendPak Inc. will pay labor costs for the first 12 months only on parts returned as previously described.

Bendpak 5-2-1 Warranty