Bendpak HD-9AE 9,000 Lbs Alignment 4-Post Lift


Factory Shipped.

  • Bendpak RBJ4500 4,500 Lb. Capacity, Rolling Bridge Jack
  • Bendpak DP-30 18 Gallon Rolling Drain Pan
  • Bendpak Caster Kit Portable Wheel Kit For HD-7 & HD-9 Series
Total Price:
$7,064.00 $5,510.00
(You save $1,554.00)
Free Shipping
Free Shipping

Factory Shipped.

Bendpak HD-9AE 9,000-lb. Capacity Alignment Car Lift 

The HD-9AE alignment lift features adjustable multiposition leveling, integrated front radius plates and rear slip plates. This makes it compatible with all leading alignment instrumentation, including 3D and camera wheel alignment systems. Multi-caster slip plates in the back and radius plates upfront allow for extremely precise, free-floating alignment. Wheel service is where many shops make the big bucks, so we’re conscious of the fact that these lifts need to be dependable and efficient to keep you satisfied.

Bendpak Leak Proof Bendpak HD-9AE Warranty Bendpak HD-9AE Floorplan

Bendpak Safe Balancing Bendpak Car Lift Guide Bendpak Top 10 Car Lift Buyer's Guide


  • 9,000-lb. maximum lifting capacity
  • CE Approved and Certified. Meets or exceeds the standards prescribed by European Standard EN-1493
  • Multi-caster slip plates
  • Dual radius plate positions
  • Heavy-duty stainless steel lifting cables
  • Dual-hub cable sheaves
  • Grease nipples on every sheave and sheave axle
  • Single hydraulic cylinder
  • Integrated hydraulic flow restrictor
  • Durable powder-coat finish
  • Spring-loaded safety locks
  • Simple push-button lock release
  • Aircraft-quality stainless steel and aluminum pneumatic cylinders
  • Secondary lock system
  • Fully enclosed cables, airlines, safety latches and sheaves
  • Multiple adjustable height locking positions
  • Maintenance-free power system
  • Easy-to-reach operator controls
  • Non-skid runways





  • Lifting Capacity*: 9,000 lbs. (4,082 kg)
  • *Max Capacity / Front Axle: 4,500 lbs. (2,041 kg)
  • *Max Capacity / Rear Axle: 4,500 lbs. (2,041 kg)


  • A - Min. Runway Height: 6.5" (165 mm)
  • B - Max. Rise: 70" (1,778 mm)
  • C - Max. Lifting Height: 76.5" (1,943 mm)
  • Time to Full Rise: 60 seconds

Outside Dimensions

  • D - Overall Width: 127" (3,226 mm)
  • E - Outside Length: 198" (5,029 mm)
  • F - Overall Length: 224" (5,690 mm)
  • G - Height of Columns: 88" (2,235 mm)

Inside Dimensions

  • H - Width Between Columns: 177" (4,496 mm)
  • I - Drive-Thru Clearance: 103.5" (2,629 mm)


  • J - Runway Width: 19" (483 mm)
  • K - Length of Runways: 188" (4,775 mm)
  • L - Width Between Runways: 40" (1,016 mm)


  • M - Min. 4-Wheel Alignment: 71" (1,803 mm)
  • N - Max. 4-Wheel Alignment: 145" (3,683 mm)
  • O - Max. 2-Wheel Alignment: 160" (4,064 mm)

Minimum Wheelbase

  • Rated Capacity: 135" (3,429 mm)
  • 75% Capacity: 115" (2,921 mm)
  • 50% Capacity: 95" (2,413 mm)
  • 25% Capacity: 80" (2,032 mm)


  • Locking Positions: 12
  • Lock Spacing: 4

Power Unit

  • Motor: 220 VAC / 60 Hz / 1 Ph
  • Noise: 45 dB
Bendpak WSA-100     Bendpak Air Bottle jack     Bendpak DP-30     Bendpak Rolling Jack 4500     Bendpak Airline Kit
          WSA-100                       AIR BOTTLE JACK                       DP-30                      ROLLING JACKS                  AIRLINE KIT

Note: An air supply (minimum: 30 psi / 3 CFM) is required for the safety-lock mechanisms to function. It is solely the responsibility of the end-user to provide, install and maintain the air supply.

*Shipping is FREE to direct points within the 48-contiguous states.

**Bendpak charges taxes to California**

**A 5% RATZ Surcharge may apply if shipping to a rural shipping point. Click here to check if you are in a RATZ zone

***It is the buyer's responsibility to unload the freight at their location.

Bendpak charges sales tax in these states California, Washington, Alabama, Arizona, Colorado, Louisiana, North Carolina, and Ohio.

BendPak 2-Post Lifts and 4-Post Lifts are warranted for five years on equipment structure, to be free of defects in material and workmanship. Power units, hydraulic cylinders, and all other assembly components such as turnplates, slip plates, cables, chains, valves, switches etc. are warranted for one year against defects in material or workmanship under normal use. BendPak Inc. shall repair or replace at their option for the warranty period those parts returned to the factory freight prepaid which prove upon inspection to be defective. BendPak Inc. will pay labor costs for the first 12 months only on parts returned as previously described.

Frequently Bought Together

Please choose options for all selected products

  • Choose Options
    • Bendpak RBJ4500 4,500 Lb. Capacity, Rolling Bridge Jack
    • Bendpak DP-30 18 Gallon Rolling Drain Pan
    • Bendpak Caster Kit Portable Wheel Kit For HD-7 & HD-9 Series