Bendpak HD-9 9,000-Lb. Capacity Standard Width 4 Post Car Lift

$4,010.00
$4,010.00
$3,355.00
(You save $655.00 )
Brand:
SKU:
5175861
Condition:
New
Availability:
Factory Shipped
Shipping:
Free Shipping
  • Bendpak JP-3 3,000-Lb. Capacity Sliding Jack Platform For Runway
  • Bendpak Plastic Drip Trays Sets Of Two
  • Bendpak RBJ4500 4,500 Lb. Capacity, Rolling Bridge Jack
  • Bendpak DP-30 18 Gallon Rolling Drain Pan
  • Bendpak Caster Kit Portable Wheel Kit For HD-7 & HD-9 Series

Bendpak HD-9 9,000-Lb. Capacity Standard Width 4 Post Car Lift

The HD-9 Series of 9,000-lb. four-post lifts contains seven different lifting models. Each car lift is perfect for vehicle storage and service, whether you’re working at the shop or from your home garage. Each model is available with optional casters, drip trays, jack platforms and more.

Bendpak Leak Proof Will it Fit? Bendpak HD-9SW Floorplan

Safe Balancing Bendpak Car Lift Guide Bendpak Top 10 Car Lift Buyer's Guide

Features:

  • 9,000-lb. maximum lifting capacity
  • CE Approved and Certified. Meets or exceeds the standards prescribed by European Standard EN-1493
  • Freestanding design
  • Perfect for parking, storage and service
  • Runways accommodate narrow and standard vehicles
  • Runways include rail-kit for optional accessories
  • Electric / hydraulic power system
  • Single hydraulic cylinder mounted underneath runway
  • Fully enclosed lifting cables, safety locks and sheaves
  • Internal anti-sway slider blocks in each column
  • Oversized self-lubricating cable rollers
  • Features heavy-duty 3/8" aircraft cable
  • Rugged 1.25" roller axles
  • Multi-position safety locks in each column
  • Adjustable lock ladders
  • Runways feature non-skid surface
  • Push-button pneumatic safety release
  • Independent backup slack-cable safety latches
  • Customizable power unit location
  • Removable approach ramps for additional drive-under clearance
  • Longer approach ramps for low-ground clearance vehicles
  • Optional drive-thru ramps available
  • Optional drip trays available
  • Optional solid deck available to increase storage capacity
  • Optional 4,500-lb. air / hydraulic rolling jacks available (Model RJ-45)
  • ETL Approved

qs.jpg

Specifications

Capacity

  • Lifting Capacity* 9,000 lbs. (4,082 kg)
  • *Max Capacity / Front Axle 4,500 lbs. (2,041 kg)
  • *Max Capacity / Rear Axle 4,500 lbs. (2,041 kg)

Rise

  • A - Min. Runway Height: 4.5" (114 mm)
  • B - Max. Rise: 70" (1,778 mm)
  • C - Max. Lifting Height: 74.5" (1,892 mm)
  • Time to Full Rise: 45 seconds

Outside Dimensions

  • D - Overall Width: 110.25" (2,800 mm)
  • E - Outside Length: 174" (4,420 mm)
  • F - Overall Length: 200" (5,080 mm)
  • G - Height of Columns: 88" (2,235 mm)

Inside Dimensions

  • H - Width Between Columns: 100.25" (2,546 mm)
  • I - Drive-Thru Clearance: 86.5" (2,197 mm)

Runways

  • J - Runway Width: 19" (483 mm)
  • K - Length of Runways: 164" (4,166 mm)
  • L - Width Between Runways: 37.5" (953 mm) or 44.375" (1,127 mm)
  • M - Runway Centerline: 56.5" (1,435 mm) or 63.375" (1,610 mm)
  • N - Outside Edge of Runways: 75.5" (1,918 mm) or 82.375" (2,092 mm)

Minimum Wheelbase

  • Rated Capacity: 115" (2,921 mm)
  • 75% Capacity: 100" (2,540 mm)
  • 50% Capacity: 85" (2,159 mm)
  • 25% Capacity: 70" (1,778 mm)

Locking

  • Locking Positions: 12
  • Lock Spacing: Every 4" (102 mm)

Power Unit

  • Motor: 220 VAC / 60 Hz / 1 Ph
  • Noise: 45 dB

Note: An air supply (minimum: 30 psi / 3 CFM) is required for the safety-lock mechanisms to function. It is solely the responsibility of the end-user to provide, install and maintain the air supply.

*Shipping is FREE to direct points within the 48-contiguous states.

**Bendpak charges taxes to California**

**A 5% RATZ Surcharge may apply if shipping to a rural shipping point. Click here to check if you are in a RATZ zone

***It is the buyer's responsibility to unload the freight at their location.

****The Bendpak HD-9 is an ALI Certified Lift. Click here to view its certification. 

BendPak 2-Post Lifts and 4-Post Lifts are warranted for five years on equipment structure, to be free of defects in material and workmanship. Power units, hydraulic cylinders, and all other assembly components such as turnplates, slip plates, cables, chains, valves, switches etc. are warranted for one year against defects in material or workmanship under normal use. BendPak Inc. shall repair or replace at their option for the warranty period those parts returned to the factory freight prepaid which prove upon inspection to be defective. BendPak Inc. will pay labor costs for the first 12 months only on parts returned as previously described.

Bendpak 5-2-1 Warranty