Bendpak HDS-14X 14,000-Lb. Capacity Extended 4 Post Car Lift

$6,755.00
$6,755.00
$5,650.00
(You save $1,105.00 )
Brand:
SKU:
5175173
Condition:
New
Availability:
Factory Shipped
Shipping:
Free Shipping
  • Bendpak DP-30 18 Gallon Rolling Drain Pan

BendPak HDS-14X 14,000-lb. Capacity Extended 4 Post Lift

  • A longer four-post lift is useful for vehicles like limos, SUVs and trucks, and that’s where the HDS-14X comes in handy. We call it our “limo style” lift because of how much front-toback clearance it offers, so you can make it over or under the lift with ease. This lift adds additional versatility and craftsmanship to your garage.

Bendpak Leak Proof Bendpak HDS-14X Warranty Bendpak HDS-14X Floorplan

Bendpak Safe Balancing Bendpak Car Lift Guide Bendpak Top 10 Car Lift Buyer's Guide

Features:

  • 14,000-lb. lifting capacity
  • CE Approved and Certified. Meets or exceeds the standards prescribed by European Standard EN-1493
  • Mid to long-style approach ramps for low ground clearance vehicles
  • Runways include rail-kit for optional accessories
  • Single hydraulic cylinder mounted underneath runway
  • Fully enclosed lifting cables, safety locks and sheaves
  • Internal anti-sway slider blocks in each column
  • Pneumatic push-button safety release
  • Features heavy-duty 1/2" aircraft cable
  • Safety locks enclosed in columns minimize pinch points
  • Oversized sheave diameter reduces cable fatigue
  • Oversized self-lubricating cable rollers
  • Rugged 1.75" roller axles
  • Multi-position safety locks in each column
  • Customizable power unit location
  • Approach ramps incorporate built-in rear-wheel chocks
  • Independent backup slack-cable safety latches
  • Runways feature non-skid surface
  • Optional drive-thru ramps available
  • Optional drip trays available
  • Optional 7,000-lb. capacity rolling jacks available (Model R​BJ7000)
  • ETL approved

qu.jpgSpecifications: 

Capacity

  • Lifting Capacity* 14,000 lbs. (6,350 kg)
  • *Max Capacity / Front Axle 7,000 lbs. (3,175 kg)
  • *Max Capacity / Rear Axle 7,000 lbs. (3,175 kg)

Rise

  • A - Min. Runway Height: 7.625" (194 mm)
  • B - Max. Rise: 70" (1,778 mm)
  • C - Max. Lifting Height: 77.625" (1,972 mm)
  • Time to Full Rise: 60 seconds

Outside Dimensions

  • D - Overall Width: 130" (3,302 mm)
  • E - Outside Length: 243" (6,172 mm)
  • F - Overall Length: 271" (6,883 mm)
  • G - Height of Columns: 93" (2,362 mm) 

Inside Dimensions

  • H - Width Between Columns: 120" (3,048 mm)
  • I - Drive-Thru Clearance: 98" (2,489 mm)

Runways

  • J - Runway Width: 20" (508 mm)
  • K - Length of Runways: 229" (5,817 mm)
  • L - Width Between Runways: 37.5" (953 mm) or 51" (1,295 mm)
  • M - Runway Centerline: 57.5" (1,461 mm) or 71" (1,803 mm)
  • N - Outside Edge of Runways: 77.5" (1,969 mm) or 91" (2,311 mm)

Minimum Wheelbase

  • Rated Capacity: 165" (4,191 mm)
  • 75% Capacity: 140" (3,556 mm)
  • 50% Capacity: 115" (2,921 mm)
  • 25% Capacity: 95" (2,413 mm)

Locking

  • Locking Positions: 13
  • Lock Spacing: Every 4" (102 mm)

Power Unit

  • Motor: 220 VAC / 60 Hz / 1 Ph
  • Noise: 45 dB

ACCESSORIES: 

Bendpak WSA-100     Bendpak Air Bottle jack     Bendpak DP-30     Bendpak Rolling Jack 7000     Bendpak Airline Kit
          WSA-100                       AIR BOTTLE JACK                       DP-30                      ROLLING JACKS                  AIRLINE KIT 

Note: An air supply (minimum: 30 psi / 3 CFM) is required for the safety-lock mechanisms to function. It is solely the responsibility of the end-user to provide, install and maintain the air supply.

*Shipping is FREE to direct points within the 48-contiguous states.

**Bendpak charges taxes to California**

**A 5% RATZ Surcharge may apply if shipping to a rural shipping point. Click here to check if you are in a RATZ zone

***It is the buyer's responsibility to unload the freight at their location.

****The Bendpak HDS-14 is an ALI Certified Lift. Click here to view its certification. 

BendPak 2-Post Lifts and 4-Post Lifts are warranted for five years on equipment structure, to be free of defects in material and workmanship. Power units, hydraulic cylinders, and all other assembly components such as turnplates, slip plates, cables, chains, valves, switches etc. are warranted for one year against defects in material or workmanship under normal use. BendPak Inc. shall repair or replace at their option for the warranty period those parts returned to the factory freight prepaid which prove upon inspection to be defective. BendPak Inc. will pay labor costs for the first 12 months only on parts returned as previously described.

Bendpak 5-2-1 Warranty