Blue-Bullet Pipe Bender Features

blue bullet logo

With its superior performance and simple operation, the Blue Bullet exhaust pipe bender will hold a special place in your shop. We took our standard bender and equipped it with a knee valve and degree plate combination for a straightforward, rugged design that will never let you down. The knee operated valve gives you precise control and hands-free bending capabilities. Simply push the lever to the left to advance the bending die and then to the right to retract it. Heavy-duty cast iron construction guarantees that the valve will stand up to years of heavy use.

Check out the Blue Bullet bender with BB-1 Die Package and BB-2 Die Package.

Quick-change bending dies

Who has time to waste? Not you. Especially when you have a car in the air and others lined up. Our competitors tried for years to come up with an effective way to swiftly switch out the bending dies. But BendPak actually did it. Our twist-lock tooling and quick-change bending dies are so effective that they are copied across the entire industry. We choose to think of imitation as the best form of flattery, but you should make sure that you get your innovative equipment from the originator and not a knock-off.

180° bending capacity
You told us you needed a bender with an extremely deep bending capability. Is a U-shape deep enough? Thought so. Be sure to ask for our 180° dies if you're planning to bend more than 170°. You'll get perfect deep bends on a 5" radius, without pipe sticking or hang ups. That's because we use an exclusive relief cut design on our bending dies to help maintain the pipe's uniformity throughout the bend cycle and eliminate excessive crimping or deformation.

3" bending capacity
We built a convenient 3" bending capacity into every BendPak bender. In fact, our 3" bending dies perfectly exemplify our commitment to quality. Take a close look at the design. They might look like ordinary bending dies, but these heavy handfuls are anything but. No other manufacturer uses our exclusive step-cut process for the die rails. Our dies feature better-contained large-sized tubing and a more uniform bend. Despite the title of "bender," this unit is actually capable of expanding and flaring too! With a full range of dies to choose from, your big tubing jobs just got a whole lot smaller.

Long-stroke bending cylinder
Because every BendPak bender is equipped with an extended-top cylinder, you no longer need to use pusher block extensions when bending with small-radius dies. Also, the 14" top-cylinder can be retracted further, providing additional clearance for changing dies or removing bent tubing.

Clampless swager
All BendPak benders are equipped with our exclusive clampless swager which puts out an incredible force of over 30,000 lbs. for quick and precise end forming. The clampless swager provides rapid set-up time and a high degree of accuracy for I.D. expansions, O.D. expansions, slip-fits, flares, ball-joints, reductions and manifold flanges. All tooling is quick release. Take a close look at the clamp assembly. You won't see a cumbersome, antiquated vise in our clamp assembly. What you will find is American ingenuity at its finest—the narrow hinged collars simply drop into position and allow for flare tubing ends as close as 3" from a bend. Don't worry about troublesome slippage either. The more pressure you put on the clamps, the tighter they grip.

Internal segment expander
Our internal segment expander is just as unique as our clampless swager and can be used for I.D. expansions, O.D. expansions, slip-fits, flares, ball-joints and manifold flanges. The buttress canister has a single position setting for all I.D. expansions, but can also be adjusted for special sizing requirements. A single arbor is used for all tubing sizes 1-1/2" - 3". Combined, the clampless swager and internal expander let you easily perform all end-finishing operations with unparalleled ease: reducing, internal swaging, flares, flat flares, ball-joints, male ball-joints, female sockets, double-donut flares and more. The Blue-Bullet is equipped with a double-ended cylinder for both the clampless swager and segment expander. A single control handle operates the cylinder and is placed towards the middle, so you can stand comfortably in one location and operate both sides.

Industrial-grade hydraulic cylinders
Integrated into every BendPak bender are commercial-grade hydraulic cylinders that feature a single-piece, pilot-fitted, machined-steel piston, wrapped with specially designed, pressure-loaded U-cup piston seals, backups and wear bands to virtually eliminate fluid bypass. The micro-smooth chrome-rod is machined from high-yield, ground and polished C-1045/50 micro-alloy steel and plated to a minimum of .001" diametrically, to ensure superior cylinder operation and life. The superior-design high durometer, mechanically-loaded rod seals make rod leakage is a thing of the past while a specially formulated abrasion-resistant urethane rod wiper provides exclusion protection. The welded cylinder body is made from robust steel tubing produced to exceed ASTM specifications. This combination of superb base material and superior processing ensures that the cylinders remain straight, smooth and last a very long time.

Durable powder coat finish
All BendPak benders feature a durable powder-coat finish that gives the metal a high-quality, extremely durable finish which can withstand even the harshest environmental or chemical conditions. Unlike other companies that claim to powder coat, we take pride in our meticulous 10-step process. First, all parts are visually inspected before being sandblasted. Afterwards, the parts are washed in our 5-stage phosphate tanks that can accommodate parts up to 25' long. Once cleaned, they're immediately dried to avoid rust production, and then outgassed. Outgassing pre-bakes the parts in a curing oven, reducing the possibility of blemishes that may be hiding in the pores of the metal. If not properly outgassed, imperfections in the metal may bubble during the curing process and most likely will cause chips in the powder. After the parts are washed and outgassed, any surfaces and / or threaded holes that need to be masked or plugged, are done so with high-temperature masking tape and silicone plugs. Next, the parts are given a quick thinner wipe to remove any light debris or fingerprints, before being hung on an electrostatically grounded conveyor line. The powder is finally applied using an electrostatic spray gun. The powder "sticks" to the surface in a fashion similar to how dust sticks to a television screen. Once the parts are powder coated, the carts are rolled into our curing oven and baked at 400° F for 45 minutes.

Optional step-by-step digital user guide
Our exhaustive BendData program features over 10,000 bending applications. The simple computer program system guides you through every step of exhaust and tailpipe fabrication. Coverage includes domestic and light trucks as far back as 1965.